HydraBlast High Pressure Wheel Washer

Hanna’s HydraBlast creates impingement and maximizes dwell time through the use of a rotating manifold that pivots to follow both the front & rear wheels. The HydraBlast utilizes Hanna’s exclusive spray head with multiple zero degree nozzles to deliver a concentrated blast of water onto the wheel surface. The freestanding modular design requires little conveyor space and is simple to add to new or existing car washes.

HydraBlast Features:

  • The HydraBlast utilizes two self rotating spray heads each with 5 nozzles (10 total on each side) delivering 18 gpm at 1000 psi.
  • The HydraBlast rotating swivel is rated to 5000 PSI for extra strength and longevity.
  • The HydraBlast Wheel Washer follows the front wheel before pivoting to follow the rear wheel.
  • The ability to follow each wheel allows for maximum dwell time and impingement.

Invader High Pressure Wheel Washer

The Invader is a fixed position high pressure applicator. The Invader utilizes the same rotating spray head configuration as the HydraBlast, but because it is fixed position it does not pivot with the movement of the vehicle wheels. The simple low maintenance design also takes less tunnel space than other low side high pressure washers. The Invader can be attached to any post or mounted with freestanding posts.

Invader Features:

  • The Invader utilizes the same rotating spray head as the HydraBlast.
  • The Invader can be used as a fixed position low side and wheel washer.
  • The Invader can be attached to any 4”x4” post to concentrate cleaning power where it is needed.

Invader_HydroBlast_web

HydraBlast & Invader High Pressure Wheel Washer Brochure

Please provide an email address where we should send the download link.

 

The Undercarriage Applicator blasts away stubborn dirt from the underside of the vehicle.

Rid the vehicle’s undercarriage of mud and road film with the high-pressure undercarriage applicator. It uses 7 high volume spray nozzles to ensure full coverage of the vehicles undercarriage.
It includes a completely stainless steel mounting tray, manifold and cover. It is also available to use a chemical application, often used with a rust inhibitor to help prevent corrosion.

Features:

  • Includes stainless steel mounting tray, manifold and cover.
  • Includes seven high volume spray nozzles for maximum undercarriage coverage.
  • Manifold can be rotated for front grill or rear bumper washing.
  • Requires a single computer function.
  • Includes solenoid valve - May be mounted remotely in equipment room.

To Download the PDF brochure, please submit your email below:

Undercarriage

Water Wizard Arch
The Hanna Water Wizard™ Arch combines Hanna and Jim Coleman technology into a powerful yet cost effective high pressure water applicator. The arch utilizes Hanna’s exclusive oscillating spray head with multiple zero degree nozzles. High pressure allows penetration into areas brushes cannot reach like wheel wells, body side moldings and roof racks. The top manifold oscillates left to right and the side manifolds up and down scrubbing the complete vehicle surface. Both top and side manifolds pivot fore and aft to provide high pressure cleaning to the hard to reach front and rear of vehicles.

The Water Wizard™ Arch can also be used as a pre-wash arch to rinse away dirt, and help loosen stuck on dirt before the wash cycle. This can be helpful for areas with intensely dirty cars from dirt or even snow.

Construction

  • Stainless Steel Frame
  • Optional Stainless Steel “Skins” w/ Graphics
  • Hydraulic Drive or Electric Drive

Standard Dimensions

Operating Space: 8’ (243 cm)
Width: 157” (398 cm)
Length: 20” (51 cm)
Height: 113” (287 cm)
Height Clearance: 96” (243 cm)

Design Features

    • Hydraulic or electric driven oscillating motion
    • Air operated pivots
    • Five oscillating spray heads
    • Four wheel washing spray heads
    • Custom graphics available
Hydraulic Flow: 3.0 GPM @ 200 PSI
(11.4 LPM @ 14 BAR)
Electrical: 60 Watts @ 24 VAC
Air: Less than 1 SCFM @ 90 PSI
Water: 35 GPM @ 1000 PSI
(133 LPM @ 69 BAR)

WaterWizardArch

Water Wizard Arch Brochure

Please provide an email address where we should send the download link.

 

COMBOARCH_pic1

Pack the most cleaning power with the Combo Water Wizard Arch!

The Hanna Combo Water Wizard Arch provides high pressure wheel washing as well as total vehicle coverage. The Combo unit utilizes Hanna’s exclusive spray head with multiple zero degree nozzles to deliver a concentrated blast of water. The Wheel Washer creates maximum impingement and maximizes dwell time through the use a rotating manifold that pivots to follow the front and rear tires. The top manifold oscillates left and right and the side manifold up and down scrubbing the complete vehicle surface. The combo unit is the ideal choice when conveyor space is limited.

Construction

  • Stainless Steel Frame
  • Optional Stainless Steel “Skins” w/ Graphics
  • Hydraulic Drive or Electric Drive

Standard Dimensions

Operating Space: 8’ (243 cm)
Width: 157” (398 cm)
Length: 20” (51 cm)
Height: 113” (287 cm)
Height Clearance: 96” (243 cm)

Design Features

    • Hydraulic or electric driven oscillating motion
    • Air operated pivots
    • Five oscillating spray heads
    • Four wheel washing spray heads
    • Custom graphics available
Hydraulic Flow: 3.0 GPM @ 200 PSI
(11.4 LPM @ 14 BAR)
Electrical: 60 Watts @ 24 VAC
Air: Less than 1 SCFM @ 90 PSI
Water: 35 GPM @ 1000 PSI
(133 LPM @ 69 BAR)

Optional Electric Drive:

  • 5 - 1/8 HP Motors Included
  • 208/230/380/415 Volt 3-Phase
  • .94/.90/.54/.50 Amp Per Motor

WaterWizardComboArch

Water Wizard Combo Arch Brochure

Please provide an email address where we should send the download link.